apple watch stuck on apple logo after screen replacement

Wait for a minute or two after your watch turns off and press and hold the side button again until you see the Apple logo. After a while it will say that it didnt unpair properly and you will have to erase from the watch itself.

Easy Way To Fix An Apple Watch Stuck On Apple Logo Rapid Repair

Simply press and hold both the side buttons and the Digital Crown simultaneously for a few seconds.

. Follow the steps below to soft restart it. Open Settings on your Apple Watch. I did a screen replacement in the AW Series 1 and it got stuck on the Apple Logo.

Open the Watch app on your iPhone. Force Restart the Apple Watch. It is still stuck on the logo.

It has disappeared from the app on my phone and I cannot repair since it wont turn on. Select Find My Apple Watch. Give Software UpdateRestore a Bit More Time to Complete.

When most devices develop issues the first approach to fix it. Apple Watch Battery Recycling. If your Apple Watch doesnt boot up past the Apple logo screen due to a weak battery you can plug it into its charger and try restarting it again.

Apple Watch Series 3Apple Watch Series 4Apple Watch Series 5Apple Watch Series 6Apple Watch SE. Heres how to reboot an Apple Watch. Try these things if you havent already to see if anything helps.

My apple watch is stuck on the apple logo I attempted a hard reset several times. Doing so does not delete any of your data and gives your Watch a fresh start. Perform a Hard Reset When Apple Watch Stuck on Logo.

Another easy trick to force your Apple Watch to go past the Apple logo screen is by attempting full battery recycling. Tap Erase All Content And Settings. Soft restarting your Apple watch might remove the Apple logo.

Erase Apple Watch Content and Settings. No worries if your Apple Watch is stuck on the Apple logo screen. Many users have reportedly fixed the issue after 2-3 rebooting.

Be patient and try the following common workarounds that could help you fix the issue. Use your Apple ID to log into Find My iPhone. Wait for the Apple Watch to turn off.

To do this first allow the Apple Watch to. Go to the watch app go to your watch and select unpair. Wait for a minute to normally boot up and power on the watch.

When your Apple Watch got stuck on the Apple logo its mostly due to software crash while turning on and your watch freezes. After finding out it Press and hold the Digital Crown and Side Button altogether for a few seconds until the Apple logo pops up on the screen. In between that time I can feel the watchs Haptic Engine go one time then the Apple Logo goes away.

If your smartwatch restarts normally you have got rid of the issue. Tap the information button lowercase i in a circle to the right of your Apple Watch. Try to Play Sound with Find My iPhone.

If restarting your watch doesnt fix. In such a case you should give the watch ample time to finish the update. If you are trying to update the watch make sure it has enough storage Watch app on iPhone General Storage.

How to Fix iOSiPadOStvOS Stuck on Apple Logo. One click of the power button the Apple Logo returns dont need to hold the power button just one click literally and it repeats. Pair your Apple Watch to your iPhone again.

If the problem still persists even after the restart try doing the same for at least 2 more times. 1 Try a hard reset Home Power button for 10 secs 2 Use a genuine Apple Lightning connector 3 Use a genuine Apple charging brick and let it charge overnight 4 Try to. Ignore that warning and wait a few minutes and you should see the ring going around the apple logo.

Pair with iPhone again. Press and hold the side button and the digital crown on your Apple Watch when the Watch shows the Apple logo. Tap All Watches in the upper left-hand corner of the screen.

It will stay on the Apple Logo for about 30 seconds - 1 minute. Enter your passcode when prompted. Once the ring closes youll have a reset apple watch and all you have to do is repair.

Long-press the Side button until the power off slider appears. One of the easiest and most basic fixes you can apply to fix the issue is to force reboot your Apple Watch. Press and hold the side button until the Power Off slider screen is shown.

Tap Erase All to confirm. If restarting your watch doesnt work try forcing it. Force Restarting Your Watch to Fix Apple Watch Frozen.

How to Fix Apple Watch Stuck on Apple Logo 1. Firstly you will need to find Digital Crown and Side Button on Apple Watch. Next drag the Power Off slider.

When your Apple Watch is stuck this is the easiest and most important thing you can do. Solve Apple Watch Stuck on Apple Logo 21 Restart Apple Watch. A bootlooping device can be caused by many things.

If you were installing a software update chances are the watch isnt stuck on the Apple logo but is simply finishing up the update before booting up. Drag the power off slider and wait for the Apple watch to turn off. 22 Force Restart the Apple Watch.

Apple watch stuck on logo after hard reset. If this works you know the battery is due for a replacement. If your watch is charging take it off the charger first.

Release when the screen goes off.

Solved Apple Watch Stuck In Boot Loop Here S How To Fix